Li4Ti5O12/Li1.3Al0.3Ti1.7(PO4)3复合负极材料的制备及其性能*
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

TM912.9

基金项目:

国家自然科学基金项目


Preparation and Characterization of Li4Ti5O12/Li1.3Al0.3Ti1.7(PO4)3 Composite
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用溶胶-凝胶法合成Li4Ti5O12/Li1.3Al0.3Ti1.7(PO4)3复合负极材料,通过X射线衍射、扫描电子显微镜、恒电流充放电、循环伏安和电化学阻抗研究复合材料的结构、形貌及电化学性能。结果表明:溶胶-凝胶法能合成纯相Li4Ti5O12/Li1.3Al0.3Ti1.7(PO4)3复合负极材料,所合成材料颗粒均匀。与纯相Li4Ti5O12相比,引入Li1.3Al0.3Ti1.7(PO4)3的Li4Ti5O12复合负极材料具有更低的锂离子嵌入/脱出阻抗,Li1.3Al0.3Ti1.7(PO4)3质量分数为1%、2%、3%、4%、5%的Li4Ti5O12复合材料首次放电容量比纯相Li4Ti5O12分别提高了6.2%、11.8%、15.5%、8.0%和2.0%。Li1.3Al0.3Ti1.7(PO4)3质量分数为3%的Li4Ti5O12复合负极材料20次循环后每次循环容量衰减率为0.022%,循环性能最好。

    Abstract:

    Li4Ti5O12/Li1.3Al0.3Ti1.7(PO4)3 composite was synthesized by sol-gel method. The structure, morphology and electrochemical performance of the composite were studied by X-ray diffractometry, scanning electron microscopy, galvanostatic charge-discharge test, cyclic voltammeter and electrochemical impedance spectroscopy techniques. Li4Ti5O12/Li1.3Al0.3Ti1.7(PO4)3 composite can be prepared by sol-gel technique and the particles of the composite are uniform. Compare with pure Li4Ti5O12, the Li4Ti5O12/Li1.3Al0.3Ti1.7(PO4)3 composite has lower Li insertion/extraction impedance. The specific capacity of the Li4Ti5O12/Li1.3Al0.3Ti1.7(PO4)3 composite doped with 1 wt%, 2 wt%, 3 wt%, 4 wt% and 5% wt% Li1.3Al0.3Ti1.7(PO4)3 is 6.2%, 11.8%, 15.5%, 8.0% and 2.0% higher than the pure Li4Ti5O12,respectively. The composite doped with 3 wt% Li1.3Al0.3Ti1.7(PO4)3 shows the best cycling performance of 0.022% capacity loss per cycle.

    参考文献
    相似文献
    引证文献
引用本文

吴显明. Li4Ti5O12/Li1.3Al0.3Ti1.7(PO4)3复合负极材料的制备及其性能*[J].精细化工,2016,33(9):

复制
分享
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:2016-03-13
  • 最后修改日期:2016-05-21
  • 录用日期:2016-05-26
  • 在线发布日期: 2016-08-17
  • 出版日期: